Acessibilidade / Reportar erro

Life cycle energy assessment and carbon dioxide emissions of wall systems for rural houses

Avaliação de ciclo de vida energético e de emissões de CO2 em sistemas de vedação para residências rurais

Abstract

Wall systems have a wide range of embodied energy due to the diversity of materials available. This paper analyzes the expenditure of energy and carbon dioxide emissions in internal and external wall systems (IEWS) of a rural residence of social interest in Cascavel, state of Paraná, Brazil. The methodology proposed by NBR ISO 14040 was used to perform a life-cycle energy assessment (LCEA) and the carbon dioxide emissions assessment (LCCO2A) of these systems. Four scenarios were considered: reinforced concrete structure and ceramic blocks wall system, load-bearing masonry with concrete blocks, steel framing and reinforced concrete walls molded on site. As a result, it was found that it is possible to reduce energy consumption up to 25% by opting for reinforced concrete walls molded on site. In regards to CO2 emission, it was verified that the difference is even greater, being able to reduce emissions by almost 32% when opting for this same scenario.

Keywords:
Building materials; Embodied energy; Sustainability

Resumo

Os sistemas de vedação têm uma ampla dispersão no valor energia incorporada devido à diversidade de materiais disponíveis. Este trabalho analisa o fluxo de energia e emissões de dióxido de carbono em sistemas de vedação vertical internas e externas (SVVIEs) de uma residência rural de interesse social localizada na cidade de Cascavel, estado do Paraná, Brasil. A metodologia proposta pela NBR ISO 14040 foi utilizada para realizar uma avaliação do ciclo de vida energético (ACVE) e a avaliação das emissões de dióxido de carbono (ACVCO2) desses sistemas. Foram considerados quatro cenários: estrutura de concreto armado com vedação de blocos cerâmicos, alvenaria estrutural com blocos de concreto, steel framing e paredes de concreto armado moldadas no local. Como resultado, constatou-se que é possível reduzir o consumo de energia em até 25%, optando pelas paredes de concreto armado moldadas in loco. Em relação à emissão de CO2, verificou-se que a diferença é ainda maior, é possível reduzir as emissões em quase 32%, utilizando este mesmo cenário.

Palavras-chave:
Materiais de construção; Energia incorporada; Sustentabilidade

Introduction

Life Cycle Assessment (LCA) is an efficient tool for reducing energy consumption and greenhouse gas emissions in buildings. The LCA is a way of systematically evaluating the environmental impacts of a product or a process throughout its lifecycle and aims to reconcile the preservation of natural resources, take preventive actions regarding pollution, improve the economic system and also maintain a sustainable ecosystem (CIAMBRONE, 1997CIAMBRONE, D. F. Environmental Life Cycle Analysis. Newport Beach: Lewis, 1997.).

Different approaches can be adopted in the LCA; in this study, two approaches were adopted: life cycle energy assessment (LCEA) and life cycle carbon emissions assessment (LCCO2A). The system analyzed includes manufacturing, maintenance, and the demolition phase of wall systems. Through the integrating LCA methods the inputs or processes that most affect sustainability can be identified, and also if these inputs are improved and environmental sustainability can be achieved more quickly (PHILLIS; KOUIKOGLOU; VERDUGO, 2017PHILLIS, Y. A.; KOUIKOGLOU, V. S.; VERDUGO, C. Computers , Environment and Urban Systems Urban sustainability assessment and ranking of cities. Computers, Environment and Urban Systems, v. 64, p. 254-265, 2017.; ATMACA; ATMACA, 2015ATMACA, A.; ATMACA, N. Life cycle energy ( LCEA ) and carbon dioxide emissions (LCCO2A) assessment of two residential buildings in Gaziantep, Turkey. Energy and Buildings, v. 102, p. 417-431, 2015.).

Sustainability assessment on walls has been carried out by other authors (LOTTEAU et al., 2015LOTTEAU, M. et al. Critical review of life cycle assessment (LCA) for the built environment at the neighborhood scale. Building and Environment, v. 93, p. 165-178, 2015.; LEOTO; LIZARRALDE, 2019LEOTO, R.; LIZARRALDE, G. Challenges in evaluating strategies for reducing a building ’ s environmental impact through Integrated Design. Building and Environment, v. 155, n. 15, p. 34-46, 2019.; MONTEIRO; FREIRE, 2012MONTEIRO, H.; FREIRE, F. Life-cycle assessment of a house with alternative exterior walls : Comparison of three impact assessment methods. Energy and Buildings, v. 47, p. 572-583, 2012.). However, these tools should be used individually so we are able to adopt the most appropriate strategy for each building (LEOTO; LIZARRALDE, 2019LEOTO, R.; LIZARRALDE, G. Challenges in evaluating strategies for reducing a building ’ s environmental impact through Integrated Design. Building and Environment, v. 155, n. 15, p. 34-46, 2019.; REZAEI; BULLE; LESAGE, 2019REZAEI, F.; BULLE, C.; LESAGE, P. Integrating building information modeling and life cycle assessment in the early and detailed building design stages. Building and Environment, v. 153, p. 158-167, 2019.). The greatest energy reduction potential incorporated in the Brazilian social interest buildings is connected to wall systems through the choice of materials and systems with less energy incorporated and greater durability, in order to reduce the necessity of maintenance and replacement of material (PAULSEN; SPOSTO, 2014PAULSEN, J. S.; SPOSTO, R. M. A life cycle energy analysis of social housing in Brazil : case study for the program “ MY HOUSE MY LIFE ”. Energy and Buildings, v. 57, n. 2013, p. 95-102, 2014.).

The objective of this study is to identify which scenario requires the most energy and which scenario results in the greatest CO2 emissions. The findings might open up strategies for future designs more sustainable. Based on our search in the literature, this paper presents the first study in the literature about LCEA and LCCO2A of four wall systems in tropical countries. This research is also distinguished by the use of exclusively Brazilian embedded energy values and CO2 emissions rates.

Method

The projects analysed

The project selected for this study was the Rural 63 model of 63.86 m² of the National Rural Housing Program - NRHP. This model was selected because it is the most frequent in rural housing complexes. Figure 1 shows a sketch of this building model.

This program aimed to build 10,000 rural houses, in different regions of Brazil. This way, common construction techniques of housing estates in the city of study were selected.

Three IEWS were used as alternatives for the conventional structural system of reinforced concrete with ceramic block wall and the projects of the respective IEWS were elaborated according to the current regulations.

Figure 1
Sketch of the selected project

Table 1 describes the scenarios analyzed. These construction systems were selected because these are the techniques most used by builders in the region.

Despite scenario 3 requiring a replacement of materials and qualified labor, we decided to analyze the steel frame as a constructive methodology, due to its agility, high level of quality and low waste generation (DUARTE; DALTRO, 2018DUARTE, D. R.; DALTRO, A. T. Light Steel framing social housing as a sustainable construction proposal. In: CONGRESSO INTERNACIONAL DE ENGENHARIA E SUSTENTABILIDADE NO SÉC. XXI, Faro, 2017. Proceedings [...] Faro:Springer, 2018.). Campos (2014CAMPOS, P. F. Light Steel Framing: uso em construções habitacionais empregando a modelagem virtual como processo de projeto e planejamento. São Paulo, 2014. 197 f. Dissertation (Master in architecture and urbanism) - Federal University of São Paulo, São Paulo, 2014.) reports that, due to the housing deficit in Brazil, faster construction methods, such as the steel frame, should be adopted. Duarte and Daltro (2018)EMPRESA DE PESQUISA ENERGÉTICA. Balanço energético nacional. Available in:Available in:http://www.epe.gov.br/pt/publicacoes-dados-abertos/publicacoes/Balanco-Energetico-Nacional-2016 . Access: jan. 2017.
http://www.epe.gov.br/pt/publicacoes-dad...
present residential buildings built with steel frames constructed in areas of social vulnerability in Brazil and claim that very few studies have been carried out on the implementation of this technique with in this context. For example, Caldas et al. (2017CALDAS, L. R. et al. Life cycle carbon emissions inventory of brick masonry and light steel framing houses in Brasilia: proposal of design guidelines for low-carbon social housing. Ambiente Construído, Porto Alegre, v. 17, n. 3, p. 71-85, jul./set. 2017.) and Ramos (2019RAMOS, V. M. K. Avaliação do ciclo de vida dos materiais de uma habitação de interesse social em alvenaria convencional, light steel framing e light wood framing. Curitiba, 2019. Dissertation (Master in Civil Engineering) - Federal University of Paraná, Curitiba, 2019.). In addition, once it is a rural area, rapid construction is preferable due to the need for labor displacement.

In order to survey the material quantities and services, the analytical compositions of National System of Research of Costs and Indices of the Civil Construction and Composition price table were used, which already consider the waste of material, labor and construction tools and equipment (CAIXA, 2007CAIXA. Sistema Nacional de Preços e Índices para a Construção Civil (SINAPI): planilhas analíticas. São Paulo, 2007.; TABELA…, 2008TABELA. TABELA DE COMPOSIÇÃO DE PREÇOS PARA ORÇAMENTOS São Paulo: PINI, 2008.).

Methodology to analyze the life cycle of the IEWS

The research focuses on a IEWSs LCA of a rural house, which for the case study is located in the city of Cascavel, state of Paraná, Brazil. The building is located ten kilometers from the urban perimeter, on the margin of BR 369 highway, at latitude: S 24º 51' 52'' longitude: W 53º 20' 18 ", at an altitude of 781 meters. According to NBR 15220-3, this region is located in bioclimatic zone 3, which requires the use of light outer walls reflecting solar radiation, cross ventilation and light thermal inertia materials (ABNT, 2005ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS. NBR 15220-3: thermal performance of buildings: part 3: Brazilian bioclimatic zoning and constructive guidelines for single-family dwellings of social interest. Rio de Janeiro, 2005.).

Following the definitions of NBR ISO 14040 incorporated energy and CO2 emissions were considered as the product of this system (ABNT, 2009ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS. NBR ISO 14040: environmental management: life cycle assessment: principles and structure. Rio de Janeiro, 2009.). As a function, there are the IEWS and as a functional unit the energy incorporated per square meter of construction (GJ/m² of construction) and CO2 emissions to these systems per square meter of the wall (kg.CO2/m² of the wall) because these are the most used units.

In order to elaborate the evaluation of the IEWS life cycle, we used the cradle-to-grave approach as already used by several authors (CABEZA et al., 2014CABEZA, L. F. et al. Life cycle assessment ( LCA ) and life cycle energy analysis ( LCEA ) of buildings and the building sector : a review. Renewable and Sustainable Energy Reviews, v. 29, p. 394-416, 2014.; ATMACA; ATMACA, 2015ATMACA, A.; ATMACA, N. Life cycle energy ( LCEA ) and carbon dioxide emissions (LCCO2A) assessment of two residential buildings in Gaziantep, Turkey. Energy and Buildings, v. 102, p. 417-431, 2015.; INGRAO et al., 2016INGRAO, C. et al. A comparative Life Cycle Assessment of external wall-compositions for cleaner construction solutions in buildings. Journal of Cleaner Production, v. 124, p. 283-298, 2016.; FILIMONAU et al., 2011FILIMONAU, V. et al. Reviewing the carbon footprint analysis of hotels : Life Cycle Energy Analysis (LCEA) as a holistic method for carbon impact appraisal of tourist accommodation. Journal of Cleaner Production, v. 19, n. 17-18, p. 1917-1930, 2011.; MUÑOS; MORALES; LETELIER, 2017MUÑOS, P. MORALES, P.; LETELIER, V.; MORA, D. Implications of Life Cycle Energy Assessment of a new school building, regarding the nearly Zero Energy Buildings targets in EU : a case of Study. Journal of Cleaner Production, v. 32, p. 142-152, 2017.). Figure 2 shows what was considered in each phase. Transport occurred from the extraction of the raw material to the deposition of the demolition material.

The pre-use phase consists of the procedures prior to the occupation of the residence. The use phase comprises the useful life of the residence. The post-use phase designates the period after the end of the useful life of the house.

Expenditure on energy and CO2 emissions with water and other building systems were not computed. CO2 emissions generated by the carbonation process that may occur in the structure were also not accounted. The life cycle duration considered in this work is 50 years, as recommended by the NBR 15575-1 (ABNT, 2013ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS. NBR 15575-1: housing buildings: performance: part 1: general requirements. Rio de Janeiro, 2013.).

Energy and CO2 emissions into material, with use of equipment and labor

In order to collect the energy incorporated into the materials, which are used in the pre-use and usage phase, a research was carried out in national studies, since the extraction, processing or manufacturing methods of each country have energy efficiency.

Table 1
Description of the scenarios

Figure 2
IEWS LCA system considered in accordance with ISO 14040

The incorporated energy used for each material was the average of the values found in the national literature. Values that would cause the average to have a coefficient of variation greater than 100% were excluded. CO2 emissions are directly linked to energy consumption, so an inventory with CO2 emission factors (from energy costs) per kilo of the material was developed.

The most relevant studies in the national literature were consulted to compose the inventory of this research. The selected works were:

  1. [1] Brazil (1982)BRAZIL. Balanço Energético de Edificações Típicas. Ministério da Indústria e Comércio, Secretaria de Tecnologia Industrial - Fundação Centro Tecnológico de Minas Gerais - CETEC, 1982.;

  2. [2] Guimarães (1985GUIMARÃES, G. D. Análise energética na construção de habitações. Rio de Janeiro, 1985. Dissertation (Master in Energy Planning Program) - Federal University of Rio de Janeiro, Rio de Janeiro, 1985.);

  3. [3] Carvalho (2002CARVALHO, J. Environmental Life Cycle Assessment applied to civil construction: case study: comparison between Portland cement with added waste. São Paulo, 2002. 105 f. Dissertation (Master in Engineering) - Polytechnic School, University of São Paulo, São Paulo, 2002.);

  4. [4] Sposto (2004)SPOSTO, R. M. et al. Management and technology for quality and sustainability of masonry components. In: CONSTRUCTION IN DEVELOPING ECONOMIES: NEW ISSUES AND CHALLENGES. Santiago, 2006. Proceedings [...] Santiago, 2006.;

  5. [5] Soares and Pereira (2004SOARES, S. R.; PEREIRA, S. W. Inventory of the ceramic production floors and bricks in the context of life cycle analysis. Jounal of the National Association of Built Environment Technology, v. 4, p. 83-94, 2004.);

  6. [6] Tavares (2007TAVARES, S. F. Metodologia de análise do ciclo de vida energético de edificações residenciais brasileiras. Florianópolis, 2007. Thesis (Doctor in Civil Engineering) - Federal University of Santa Catarina, Florianópolis, 2007.);

  7. [7] Stachera Junior and Casagrande Junior (2007)STACHERA JUNIOR, T.; CASAGRANDE JUNIOR, E. Avaliação de emissões de CO2 na construção civil: um estudo de caso da habitação de interesse social no Paraná. In: ENCONTRO NACIONAL SOBRE GESTÃO EMPRESARIAL E MEIO AMBIENTE, 9., Curitiba, 2000. Anais […] Curitiba, 2000.;

  8. [8] Lobo (2010LOBO, F. H. R. Inventário de emissão equivalente de dióxido de carbono e energia embutida na composição de serviços em obras públicas: estudo de caso no estado do Paraná. Curitiba, 2010. Dissertation (Master in Civil Engineering) - Federal University of Paraná, Curitiba, 2010.);

  9. [9] Graf (2011GRAF, H. F. Transmitância térmica e energia incorporada na arquitetura: sua relação nas superfícies do invólucro de uma edificação residencial unifamiliar conforme a norma NBR 12721. Curitiba, 2011. Dissertation (Master in Civil Engineering) - Federal University of Paraná, Curitiba, 2012.);

  10. [10] Nabut Neto (2011NABUT NETO, A. C. Energia incorporada e emissões de CO2 de fachadas: estudo de caso do steel frame para utilização em Brasília. Brasilia, 2011. Dissertation (Master in Civil Engineering) - University of Brasilia, 2011.);

  11. [11] Costa (2012COSTA, B. L. C. Quantification of carbon dioxide releases generated by the production of building materials in Brazil. Rio de Janeiro, 2012. 208 f. Dissertation (Master in Civil Engineering) - Federal University of Rio de Janeiro, Rio de Janeiro, 2012.);

  12. [12] Carminatti Junior (2012CARMINATTI JUNIOR, R. Analysis of the life cycle energy of a social interest housing project conceived in light steel framing. 2012. 164 f. Thesis (PhD Civil Engineering programs) Federal University of São Carlos, São Carlos, 2012.);

  13. [13] Taborianski and Prado (2012TABORIANSKI, V. M.; PRADO, R. T. A. Methodology of CO2 Emission in the Life Cycle of Office Building Facades. Environmental Impact Assessment Review, v. 33, p. 41-47, 2012.);

  14. [13] Silva (2013SILVA, B. V. Construção de ferramenta para avaliação do ciclo de vida de edificações. São Paulo, 2013. Dissertation (Master in Civil Engineering) - University of São Paulo, São Paulo, 2013.);

  15. [14] Souza (2013SOUZA, R. V. Aspectos ambientais e de custo de produção do Sistema Plataforma em madeira para habitação de interesse social: estudo de caso em Florianópolis. Florianopolis, 2013. Dissertation (Master in Civil Engineering) - Federal University of Santa Catarina, Florianópolis, 2013.);

  16. [15] Falcão (2013FALCÃO, C. M. B. B. Analysis of investment quality and CO2 associated with the production of recycled aggregates in the Metropolitan Region of São Paulo. São Paulo, 2013. 188 f. Course Conclusion Paper (Graduation in Engineering Civil) - Polytechnic School of the University of São Paulo, São Paulo, 2013.);

  17. [16] Silva and Silva (2015SILVA, V. G.; SILVA, M. G. Seleção de materiais e edifícios de alto desempenho ambiental. In: GONÇALVES, J. C. S.; BODE, K. (Org.).Edifício ambiental. São Paulo: Oficina de Textos, 2015.); and

  18. [17] Pedroso (2015PEDROSO, G. M. Avaliação de ciclo de vida energético (ACVE) de sistemas de vedação de habitações. Brasilia, 2015. Thesis (Doctor in Civil Engineering) - BrasíliaUniversity, 2015.).

Table 2 shows the average of the values of embodied energy and CO2 emissions found in the literature.

Some services require equipment (such as an immersion vibrator and drill). In this case, the power of the equipment and the number of hours of use were obtained from the SINAPI spreadsheets. The energy for the use of equipment was calculated from this information in all the analyzed phases. The electrical energy conversion factor for CO2 emissions used was 0.038 kg.CO2/MJ (EMPRESA…, 2017EMPRESA DE PESQUISA ENERGÉTICA. Balanço energético nacional. Available in:Available in:http://www.epe.gov.br/pt/publicacoes-dados-abertos/publicacoes/Balanco-Energetico-Nacional-2016 . Access: jan. 2017.
http://www.epe.gov.br/pt/publicacoes-dad...
).

Energy spent by labor was calculated using the conversion factor proposed by Bouchard et al. (1983)BOUCHARD, C. et al. A method to assess energy expenditure in children and adults. American Journal of Clinical Nutrition, v. 37, n. 3, p. 461-470, mar. 1983. and the number of working hours calculated from the SINAPI spreadsheets.

Table 2
Embodied energy and CO2 emissions considered

Energy and CO2 emissions coming from transport

At all stages of the life cycle of IEWS there are energy costs and emissions arising from the need to transport materials, waste and workers. Thus, energy spent with materials and waste transport was estimated according to the distance between the point of extraction or manufacturing and commercialization, and between the point of sale and use. The energy consumption was calculated using the load capacity and average consumption from Refs. Ministry of the Environment (2014) and Energy Research Company (2017). The value of 1.44 MJ/ton/km was considered for light vehicles and 0.69 MJ/ton/km for medium trucks. The CO2 emission factors used to compute emissions with transport considered refers to 2.681 kg.CO2/L of diesel oil (GHG PROTOCOL, 2017GHG PROTOCOL. Calculation tools. Available in:Available in:https://ghgprotocol.org/calculation-tools . Access:jan. 2017.
https://ghgprotocol.org/calculation-tool...
).

Energy and CO2 emissions from the use phase

To obtain the maintenance energy, Equation 1 was used; it estimates the energy of replacement of each material (RAMESH; PRAKASH; SHUKLA, 2010RAMESH, T.; PRAKASH, R.; SHUKLA, K. K. Life cycle energy analysis of buildings : an overview. Energy and Buildings, v. 42, p. 1592-1600, 2010.).

M E = E I × M i [ ( L B / L M ) - 1 ] Eq. 1

Where:

ME is the maintenance energy;

EI is the content of energy of the material (i) per unit;

Mi is the amount of building material (i);

LB is the life span of the building; and

LM is the and life span of the material (i).

LB considered is 50 years (ABNT, 2003). LM average for indoor painting is 3.5 years and for outdoor painting is 10 years (ABNT, 2013ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS. NBR 15575-1: housing buildings: performance: part 1: general requirements. Rio de Janeiro, 2013.). In addition to painting, steel framing walls require replacement of some materials, the cementitious plates must be replaced in 40 years and OSB sheets and gypsum plates in 30 years (PALÁCIO, 2013PALÁCIO, C. D. U. Análise térmica e energia incorporada de vedações para habitações de interesse social: Estudo de caso com utilização do steel frame no entorno do DF. Brasilia, 2013. Dissertation (Master in Civil Engineering) - University of Brasilia, 2013.).

To evaluate CO2 emissions in the use phase, the emission factors per kilogram of material multiplied by the amount of spare materials were used (this factors were showed in Table 2).

In this phase, the energy spent on labor was calculated as proposed by Bouchard et al. (1983)BOUCHARD, C. et al. A method to assess energy expenditure in children and adults. American Journal of Clinical Nutrition, v. 37, n. 3, p. 461-470, mar. 1983.

Energy and CO2 emissions from the post-use phase

To obtain the energy in the demolition or deconstruction phase and to determine the CO2 emissions with demolition or deconstruction, the factors indicated by Caldas (2016CALDAS, L. R. Life cycle energy assessment (LCEA) and the thermal performance of a light steel framing housing with the use of different types of thermal insulation. Electronic Journal of Civil Engineering, v. 11, p. 1-14, 2016.) based in Brazilian experience, which include the use of equipment and labor, were utilized.

Energy and CO2 emissions resulting from transporting waste from the construction site to the material disposal site were accounted in the same way as in the pre-use and use phase.

Results and discussion

Energy incorporated into IEWS

By analyzing

Figure 3 shows that S4 requires a considerably larger amount than the other scenarios in the pre-use phase, which includes extraction, fabrication or processing, transportation, human labor and equipment use in the construction of the IEWS, this behavior is due to the high energy value incorporated into the aluminum frames.

However, there is the possibility of multiple uses of the same forms when there is a repetition of the same model of housing unit, taking into account that the case study project is a housing of social interest and it is known that this type of building is replicated several times. Thus, a reduction of the energy of the pre-use phase with the reutilization of the aluminum forms is observed, according to Figure 3.

Pedroso (2015PEDROSO, G. M. Avaliação de ciclo de vida energético (ACVE) de sistemas de vedação de habitações. Brasilia, 2015. Thesis (Doctor in Civil Engineering) - BrasíliaUniversity, 2015.) in his research on energy incorporated into IEWS in a case study for the Federal District obtained 2.02 GJ/m² of energy in the pre-use phase for a scenario similar to S1 of this work. As for load-bearing masonry with concrete blocks (wall system similar to S2) the same author found the value of 1.21 GJ/m² while in this work the value reached was 1.94 GJ/m². These differences can be explained by the energy spent with transport, the distances between extraction point and manufacturing to construction are different depending on the location of the case study.

Figure 4 shows the pre-use energy for scenario S4 for several numbers of reuse. A reduction of the pre-use energy with 100 reuses is observed, but from 500 reuses to 1000 there are no significant reductions. Comparing with the pre-use energy of the other scenarios it is noticed that with 100 repetitions S4 already becomes more efficient than the others. For this study, 100 reuses of aluminum formwork was adopted, although it is possible to reuse it more often, however, rural housing condominiums rarely exceed 100 homes.

Figure 3
Pre-use energy of each scenario

Figure 4
Pre-use energy of S4 using recycled aluminum molds and virgin aluminum molds for various uses

There is also the possibility of using recycled aluminum for the manufacture of aluminum molds. In the first use there would be a great difference in the energy embedded in the scenario, however, with the increase of the uses this difference would be reduced as shown in Figure 4. Then, for the rest of this work, 100 reuses of virgin aluminum molds were considered.

In the use phase of the building, the energy that is used in the IEWS is the one of maintenance. In this case S1, S2 and S4 have similar performances, since they only require the painting service, however, S3 (steel frame) requires some material replacement, so this scenario required 1.48 GJ/m² as shown by Figure 5.

Figure 5 also shows the energy incorporated in the post-use phase, which involves demolition or deconstruction; the energy required by S3 is reduced in relation to the others, this is due to two factors: lower mass of this scenario and the deconstruction factor is smaller than that of demolition, as it does not require the use of large fossil-fueled engines.

Pedroso (2015PEDROSO, G. M. Avaliação de ciclo de vida energético (ACVE) de sistemas de vedação de habitações. Brasilia, 2015. Thesis (Doctor in Civil Engineering) - BrasíliaUniversity, 2015.) estimated the energy expenditure in demolition/deconstruction by means of prototype tests of 1.0 m². Using this methodology, the author obtained the value of 0.036 GJ/m² for conventional wall system (S1), 0.033 GJ/m² for load-bearing masonry (S2), 0.011 for steel framing (S3) and 0.030 GJ/m² for concrete wall (S4). These values do not consider human labor and the transportation of waste generated by deconstruction.

By analyzing the life cycle of the four scenarios, it is observed that S1 requires 3.19 GJ/m², S2 requires 2.89 GJ/m², S3 requires 3.47 GJ/m² and S4 demands 2.60 GJ/m². Therefore, considering the life cycle of the IEWS analyzed, S4 requires less amount of energy per square meter of construction and S3 has the highest demand.

By analyzing Figure 5 it can be seen that the phase of the life cycle that most influences the IEWS energy requirement is the pre-use phase, followed by the phase of use, whereas the post-use phase does not have great expressiveness. However, energy is only one of the environmental performance parameters of IEWS; the mass and volume of material to be discarded are some of the factors that must also be analyzed.

However, the energy spent with transport in S3 is significantly lower than in the other scenarios, as shown in Figure 6, which compares the energy spent on transport and the total gross energy of each scenario. This behavior can be explained by the specific mass of the steel frame system being smaller than the specific mass of the other wall systems.

Figure 5
Energy in the pre-use phase, use-phase and post-use phase of the live cycle of IEWS

Figure 6
Comparison between the energy incorporated into the materials, energy spent on transport and the total gross energy of each scenario

Figure 6 shows the comparison of the energy incorporated into the materials with the total gross energy of each scenario and also shows that a large part of the total gross energy of S3 is due to the incorporated energy of the building materials used in this system, which corresponds to 95.19% of the total gross energy. In the other scenarios this percentage is lower, in the conventional system the energy incorporated into the materials corresponds to 76.63% of the total gross energy, in the load-bearing masonry to 67.00% and in the wall of molded concrete on site this percentage is 77.64%.

Emissions from the life cycle of the IEWS

In a similar way to energy, CO2 emissions are the majority in the pre-use phase, however, as it is possible to see in Figure 7, when the function of the LCA are the CO2 emissions, S1 is the one with the highest values and S3 is the one which presents lower values in the pre-use phase.

As shown in Figure 7, in the use phase emissions are more significant in S3 due to the need to replace more materials than the other scenarios. In S1, S2 and S4 the values are the same, since the replacement of materials and the maintenance service are equivalent for all.

In turn, Figure 7 shows yet CO2 emissions in the post-use phase. In this case, S3 is the one that has the lowest emission value; this is due to the method of disassembling the steel framing and its reduced mass.

Therefore, by analyzing CO2 emissions throughout the life cycle of the IEWS, we can see that the scenario with the lowest value is S4. Adding the CO2 emissions in the three phases S1 emits 87.22 kg. CO2/m² of wall, S2 emits 82.04 kg. CO2/ m² of wall, S3 emits 72.71 kg. CO2/m² of wall and S4 emits 59. 67 kg. CO2 /m² of wall.

Nabut Neto (2011NABUT NETO, A. C. Energia incorporada e emissões de CO2 de fachadas: estudo de caso do steel frame para utilização em Brasília. Brasilia, 2011. Dissertation (Master in Civil Engineering) - University of Brasilia, 2011.) in a similar scenario to S1 computed 85 kg.CO2/m² of wall. For a similar scenario to S4, Mequignon et al. (2013MEQUIGNON, M. et al. Impact of the lifespan of building external walls on greenhouse gas index. Building and Environment, v. 59, p. 654-661, 2013.) obtained the value of 65.10 kg.CO2/m².

S4 emits 5.81 kg. CO2 per cubic meter of wall, however, in a study on emissions of concrete walls for soil containment Martí, Yepes and Molina-Moreno (2017MARTÍ, V.; YEPES, V.; MOLINA-MORENO, F. Carbon embodied optimization for buttressed earth-retaining walls : Implications for low-carbon conceptual designs. Journal of Cleaner Production, v. 164, p. 872-884, 2017.) obtained 11.05 kg.CO2/m², this occurs because retaining walls require a concrete with higher strength, which reflects in the higher consumption of steel and cement per cubic meter and, according to Zastrow et al. (2017ZASTROW, P. et al. Life cycle assessment of cost-optimized buttress earth-retaining walls : a parametric study. Journal of Cleaner Production, v. 140, p. 1037-1048, 2017.), cement and steel account for most of the energy embedded in retaining walls.

Islam et al. (2014ISLAM, H. et al. Life cycle assessment and life cycle cost implications of wall assemblages designs. Energy & Buildings, v. 84, p. 33-45, 2014.) in a study of Australia's typical wall systems, ceramic brick, concrete block and wood closures, concluded that wood closures are responsible for a smaller amount of emissions than the others. Huang et al. (2018HUANG, L. et al. Life cycle assessment and life cycle cost of university dormitories in the southeast China : case study of the university town of Fuzhou. Journal of Cleaner Production, v. 173, p. 151-159, 2018.), in a study on energy incorporated in dormitories of Chinese universities also found that the structures of wood have lower emissions, thus, wood becomes another option for alternative wall systems in Brazil.

Figure 8 compares the emissions generated by transport with the total gross emissions of each scenario. S3 generates less emissions, this can be explained by the fact that this scenario requires less transport service for workers and materials.

Unlike emissions with transport, in the CO2 emissions incorporated into the materials, that is, from the extraction, processing or manufacture of the materials, S3 is the one that generates more CO2 emissions. Figure 8 shows that emissions from S1 and S3 generate near quantities.

Waste coming from the IEWS

With regard to the residues produced by each IEWS with wastes in the demolition or deconstruction, S1, S2 and S4 present close values, however, in S3 the mass of residues is considerably smaller (Figure 9).

Regarding Figure 9 and 6, we can see that the energy consumption is also not related to the mass of waste, since S3 is the one that has the highest energy consumption and is the lightest among the studied scenarios.

Comparing Figure 9 with Figure 8, we also can see that the mass of materials used in construction is not related to the mass of emissions, since S4, despite having the largest mass of waste, has the lowest CO2 emissions.

General analysis of the life cycle of the IEWS

Figure 10 shows the CO2 emissions and the energy incorporated into the life cycle of each scenario, from this it is possible to notice that S4 presents the lowest values for both functions; however, as shown in Figure 9, this same scenario generates the largest mass of waste.

Analyzing Figure 6 and Figure 8 we can note that transport and materials are responsible for great part of the energy consumed and CO2 emissions. Bearing this in mind, Table 3 shows the percentages of energy and emissions from other sources and emphasizes that they are not values of great participation.

Figure 7
CO2 emissions in the pre-use phase, use-phase and post-use phase of the live cycle of IEWS

Figure 8
Comparison between emissions incorporated into the materials, emissions originating from transport and the total gross emissions of each scenario

Figure 9
Mass of solid residue from wall systems including waste

Figure 10
Comparison of the energy incorporated with the CO2 emissions in each scenario

Table 3
Percentage of energy and emissions from labor and use of equipment

Conclusions

Evaluating the energy life cycle and CO2 emissions of wall systems for rural housing of social interest in Brazil, it is concluded that:

S4 is the wall system with lower incorporated energy, considering that there are 100 different uses of the virgin aluminum molds. S4 is also the scenario that emits less amount of CO2 during its life cycle, considering the same conditions of use of molds that had already been described;

for the conditions of this study, the scenario that would consume more energy over the life cycle is S3;

regarding CO2 emissions, S1 scenario was less sustainable;

we emphasize that this is a case study for the region of Cascavel, Paraná, and due to transport issues, the values of incorporated energy and CO2 emissions can suffer significant variations for other regions; and

one of the difficulties that ware found during the study was the lack of standardization of the measurement units.

References

  • ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS. NBR 15220-3: thermal performance of buildings: part 3: Brazilian bioclimatic zoning and constructive guidelines for single-family dwellings of social interest. Rio de Janeiro, 2005.
  • ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS. NBR ISO 14040: environmental management: life cycle assessment: principles and structure. Rio de Janeiro, 2009.
  • ASSOCIAÇÃO BRASILEIRA DE NORMAS TÉCNICAS. NBR 15575-1: housing buildings: performance: part 1: general requirements. Rio de Janeiro, 2013.
  • ATMACA, A.; ATMACA, N. Life cycle energy ( LCEA ) and carbon dioxide emissions (LCCO2A) assessment of two residential buildings in Gaziantep, Turkey. Energy and Buildings, v. 102, p. 417-431, 2015.
  • BOUCHARD, C. et al. A method to assess energy expenditure in children and adults. American Journal of Clinical Nutrition, v. 37, n. 3, p. 461-470, mar. 1983.
  • BRAZIL. Balanço Energético de Edificações Típicas. Ministério da Indústria e Comércio, Secretaria de Tecnologia Industrial - Fundação Centro Tecnológico de Minas Gerais - CETEC, 1982.
  • CABEZA, L. F. et al. Life cycle assessment ( LCA ) and life cycle energy analysis ( LCEA ) of buildings and the building sector : a review. Renewable and Sustainable Energy Reviews, v. 29, p. 394-416, 2014.
  • CAIXA. Sistema Nacional de Preços e Índices para a Construção Civil (SINAPI): planilhas analíticas. São Paulo, 2007.
  • CALDAS, L. R. Life cycle energy assessment (LCEA) and the thermal performance of a light steel framing housing with the use of different types of thermal insulation. Electronic Journal of Civil Engineering, v. 11, p. 1-14, 2016.
  • CALDAS, L. R. et al. Life cycle carbon emissions inventory of brick masonry and light steel framing houses in Brasilia: proposal of design guidelines for low-carbon social housing. Ambiente Construído, Porto Alegre, v. 17, n. 3, p. 71-85, jul./set. 2017.
  • CAMPOS, P. F. Light Steel Framing: uso em construções habitacionais empregando a modelagem virtual como processo de projeto e planejamento. São Paulo, 2014. 197 f. Dissertation (Master in architecture and urbanism) - Federal University of São Paulo, São Paulo, 2014.
  • CARMINATTI JUNIOR, R. Analysis of the life cycle energy of a social interest housing project conceived in light steel framing. 2012. 164 f. Thesis (PhD Civil Engineering programs) Federal University of São Carlos, São Carlos, 2012.
  • CARVALHO, J. Environmental Life Cycle Assessment applied to civil construction: case study: comparison between Portland cement with added waste. São Paulo, 2002. 105 f. Dissertation (Master in Engineering) - Polytechnic School, University of São Paulo, São Paulo, 2002.
  • CIAMBRONE, D. F. Environmental Life Cycle Analysis. Newport Beach: Lewis, 1997.
  • COSTA, B. L. C. Quantification of carbon dioxide releases generated by the production of building materials in Brazil. Rio de Janeiro, 2012. 208 f. Dissertation (Master in Civil Engineering) - Federal University of Rio de Janeiro, Rio de Janeiro, 2012.
  • DUARTE, D. R.; DALTRO, A. T. Light Steel framing social housing as a sustainable construction proposal. In: CONGRESSO INTERNACIONAL DE ENGENHARIA E SUSTENTABILIDADE NO SÉC. XXI, Faro, 2017. Proceedings [...] Faro:Springer, 2018.
  • EMPRESA PARANAENSE DE ASSISTÊNCIA TÉCNICA E EXTENSÃO RURAL. Moradia rural: o programa. Available in: Available in: http://www.emater.pr.gov.br/modules/conteudo/conteudo.php?conteudo=182 Access: jan. 2017.
    » http://www.emater.pr.gov.br/modules/conteudo/conteudo.php?conteudo=182
  • EMPRESA DE PESQUISA ENERGÉTICA. Balanço energético nacional. Available in:Available in:http://www.epe.gov.br/pt/publicacoes-dados-abertos/publicacoes/Balanco-Energetico-Nacional-2016 Access: jan. 2017.
    » http://www.epe.gov.br/pt/publicacoes-dados-abertos/publicacoes/Balanco-Energetico-Nacional-2016
  • FALCÃO, C. M. B. B. Analysis of investment quality and CO2 associated with the production of recycled aggregates in the Metropolitan Region of São Paulo. São Paulo, 2013. 188 f. Course Conclusion Paper (Graduation in Engineering Civil) - Polytechnic School of the University of São Paulo, São Paulo, 2013.
  • FILIMONAU, V. et al. Reviewing the carbon footprint analysis of hotels : Life Cycle Energy Analysis (LCEA) as a holistic method for carbon impact appraisal of tourist accommodation. Journal of Cleaner Production, v. 19, n. 17-18, p. 1917-1930, 2011.
  • GHG PROTOCOL. Calculation tools. Available in:Available in:https://ghgprotocol.org/calculation-tools Access:jan. 2017.
    » https://ghgprotocol.org/calculation-tools
  • GRAF, H. F. Transmitância térmica e energia incorporada na arquitetura: sua relação nas superfícies do invólucro de uma edificação residencial unifamiliar conforme a norma NBR 12721. Curitiba, 2011. Dissertation (Master in Civil Engineering) - Federal University of Paraná, Curitiba, 2012.
  • GUIMARÃES, G. D. Análise energética na construção de habitações. Rio de Janeiro, 1985. Dissertation (Master in Energy Planning Program) - Federal University of Rio de Janeiro, Rio de Janeiro, 1985.
  • HUANG, L. et al. Life cycle assessment and life cycle cost of university dormitories in the southeast China : case study of the university town of Fuzhou. Journal of Cleaner Production, v. 173, p. 151-159, 2018.
  • INGRAO, C. et al. A comparative Life Cycle Assessment of external wall-compositions for cleaner construction solutions in buildings. Journal of Cleaner Production, v. 124, p. 283-298, 2016.
  • ISLAM, H. et al. Life cycle assessment and life cycle cost implications of wall assemblages designs. Energy & Buildings, v. 84, p. 33-45, 2014.
  • LEOTO, R.; LIZARRALDE, G. Challenges in evaluating strategies for reducing a building ’ s environmental impact through Integrated Design. Building and Environment, v. 155, n. 15, p. 34-46, 2019.
  • LOBO, F. H. R. Inventário de emissão equivalente de dióxido de carbono e energia embutida na composição de serviços em obras públicas: estudo de caso no estado do Paraná. Curitiba, 2010. Dissertation (Master in Civil Engineering) - Federal University of Paraná, Curitiba, 2010.
  • LOTTEAU, M. et al. Critical review of life cycle assessment (LCA) for the built environment at the neighborhood scale. Building and Environment, v. 93, p. 165-178, 2015.
  • MARTÍ, V.; YEPES, V.; MOLINA-MORENO, F. Carbon embodied optimization for buttressed earth-retaining walls : Implications for low-carbon conceptual designs. Journal of Cleaner Production, v. 164, p. 872-884, 2017.
  • MEQUIGNON, M. et al. Impact of the lifespan of building external walls on greenhouse gas index. Building and Environment, v. 59, p. 654-661, 2013.
  • MINISTÉRIO DO MEIO AMBIENTE. Inventário nacional de emissões atmosféricas por veículos automotores rodoviários. 2011. Available in: Available in: https://www.mma.gov.br/estruturas/163/_publicacao/163_publicacao27072011055200.pdf Access: jan. 2017.
    » https://www.mma.gov.br/estruturas/163/_publicacao/163_publicacao27072011055200.pdf
  • MONTEIRO, H.; FREIRE, F. Life-cycle assessment of a house with alternative exterior walls : Comparison of three impact assessment methods. Energy and Buildings, v. 47, p. 572-583, 2012.
  • MUÑOS, P. MORALES, P.; LETELIER, V.; MORA, D. Implications of Life Cycle Energy Assessment of a new school building, regarding the nearly Zero Energy Buildings targets in EU : a case of Study. Journal of Cleaner Production, v. 32, p. 142-152, 2017.
  • NABUT NETO, A. C. Energia incorporada e emissões de CO2 de fachadas: estudo de caso do steel frame para utilização em Brasília. Brasilia, 2011. Dissertation (Master in Civil Engineering) - University of Brasilia, 2011.
  • PALÁCIO, C. D. U. Análise térmica e energia incorporada de vedações para habitações de interesse social: Estudo de caso com utilização do steel frame no entorno do DF. Brasilia, 2013. Dissertation (Master in Civil Engineering) - University of Brasilia, 2013.
  • PAULSEN, J. S.; SPOSTO, R. M. A life cycle energy analysis of social housing in Brazil : case study for the program “ MY HOUSE MY LIFE ”. Energy and Buildings, v. 57, n. 2013, p. 95-102, 2014.
  • PEDROSO, G. M. Avaliação de ciclo de vida energético (ACVE) de sistemas de vedação de habitações. Brasilia, 2015. Thesis (Doctor in Civil Engineering) - BrasíliaUniversity, 2015.
  • PHILLIS, Y. A.; KOUIKOGLOU, V. S.; VERDUGO, C. Computers , Environment and Urban Systems Urban sustainability assessment and ranking of cities. Computers, Environment and Urban Systems, v. 64, p. 254-265, 2017.
  • RAMESH, T.; PRAKASH, R.; SHUKLA, K. K. Life cycle energy analysis of buildings : an overview. Energy and Buildings, v. 42, p. 1592-1600, 2010.
  • RAMOS, V. M. K. Avaliação do ciclo de vida dos materiais de uma habitação de interesse social em alvenaria convencional, light steel framing e light wood framing. Curitiba, 2019. Dissertation (Master in Civil Engineering) - Federal University of Paraná, Curitiba, 2019.
  • REZAEI, F.; BULLE, C.; LESAGE, P. Integrating building information modeling and life cycle assessment in the early and detailed building design stages. Building and Environment, v. 153, p. 158-167, 2019.
  • SILVA, B. V. Construção de ferramenta para avaliação do ciclo de vida de edificações. São Paulo, 2013. Dissertation (Master in Civil Engineering) - University of São Paulo, São Paulo, 2013.
  • SILVA, V. G.; SILVA, M. G. Seleção de materiais e edifícios de alto desempenho ambiental. In: GONÇALVES, J. C. S.; BODE, K. (Org.).Edifício ambiental. São Paulo: Oficina de Textos, 2015.
  • SOARES, S. R.; PEREIRA, S. W. Inventory of the ceramic production floors and bricks in the context of life cycle analysis. Jounal of the National Association of Built Environment Technology, v. 4, p. 83-94, 2004.
  • SOUZA, R. V. Aspectos ambientais e de custo de produção do Sistema Plataforma em madeira para habitação de interesse social: estudo de caso em Florianópolis. Florianopolis, 2013. Dissertation (Master in Civil Engineering) - Federal University of Santa Catarina, Florianópolis, 2013.
  • SPOSTO, R. M. et al. Management and technology for quality and sustainability of masonry components. In: CONSTRUCTION IN DEVELOPING ECONOMIES: NEW ISSUES AND CHALLENGES. Santiago, 2006. Proceedings [...] Santiago, 2006.
  • STACHERA JUNIOR, T.; CASAGRANDE JUNIOR, E. Avaliação de emissões de CO2 na construção civil: um estudo de caso da habitação de interesse social no Paraná. In: ENCONTRO NACIONAL SOBRE GESTÃO EMPRESARIAL E MEIO AMBIENTE, 9., Curitiba, 2000. Anais […] Curitiba, 2000.
  • TABELA. TABELA DE COMPOSIÇÃO DE PREÇOS PARA ORÇAMENTOS São Paulo: PINI, 2008.
  • TABORIANSKI, V. M.; PRADO, R. T. A. Methodology of CO2 Emission in the Life Cycle of Office Building Facades. Environmental Impact Assessment Review, v. 33, p. 41-47, 2012.
  • TAVARES, S. F. Metodologia de análise do ciclo de vida energético de edificações residenciais brasileiras. Florianópolis, 2007. Thesis (Doctor in Civil Engineering) - Federal University of Santa Catarina, Florianópolis, 2007.
  • ZASTROW, P. et al. Life cycle assessment of cost-optimized buttress earth-retaining walls : a parametric study. Journal of Cleaner Production, v. 140, p. 1037-1048, 2017.

Publication Dates

  • Publication in this collection
    13 Nov 2020
  • Date of issue
    Jan-Mar 2021

History

  • Received
    14 June 2019
  • Accepted
    04 Aug 2020
Associação Nacional de Tecnologia do Ambiente Construído - ANTAC Av. Osvaldo Aranha, 93, 3º andar, 90035-190 Porto Alegre/RS Brasil, Tel.: (55 51) 3308-4084, Fax: (55 51) 3308-4054 - Porto Alegre - RS - Brazil
E-mail: ambienteconstruido@ufrgs.br